High-Performance Vertical Closet

High-Performance Cased/Closet Rear-Return

Part Number: C2-G

The Cased/Closet Vertical Bottom Supply with Rear Return (C2-G) is a high performance, high-static (up to .50 ESP), ducted vertical fan coil. Primarily used in floor-mounted or hideaway applications, the C2-G is furred into partition walls, hidden closets, or utility rooms with a ducted discharge. A removable access panels facilitate easy servicing. The C2-G comes with comes with a coil, easy slide-out blower/motor assembly with quick-connect plug and a galvanized steel, powder-coated epoxy drain pan covered with ⅛-inch thick insulation. The galvanized steel cabinet is insulated with ½-inch thick, over three-pound density, neoprene-coated fiberglass. A one-inch duct flange on return- and supply-air openings is standard.

Cooling Capacity

C2 Series Hi-Performance Vertical fan coils have been rated in accordance with AHRI Standard 440-2005 for room fan-coil air-conditioners and are certified by AHRI to meet the following product performance ratings:

Based on 80°F DB and 67°F WB EAT, 45°F EWT, 10°F temperature rise, high fan speed. Motor voltage 115/1/60 power source. Air flow under dry coil conditions. Water pressure drops shown in feet of water.

Heating Performance

Based on 70°F DB EAT, 180°F EWT, 40°F temperature drop, high fan speed. Motor voltage 115/1/60 power source.
Air flow under dry coil conditions. Water pressure drops shown in feet of water.

Features

400 to 2,200 CFM
High-static ducted vertical fan coil, manufactured of heavy-gauge galvanized steel and insulated with 1/2″ thick, over three-pound density, neoprene-coated fiberglass; insulated drain pan with primary and secondary drain connections constructed of galvanized metal and finished with a powder-coated epoxy, easily removable motor/blower assembly with quick-connect plug
Bottom-supply with rear return
Primarily used in vertical floor-mounted or hideaway applications the unit is furred into partition walls or hidden in closets, utility rooms and other concealed locations with a ducted discharge
Rear access panel is removable for easy maintenance
One-inch discharge duct flange is standard on the top panel
Coils are manufactured of copper tube with aluminum fins and are 100% underwater pressure tested to 350 PSI with a 300 PSI working pressure
Galvanized drain pan is finished with a powder-coated epoxy, 1/8″ thick insulation and features primary and secondary drain connections
Three-speed, 115/1/60 motor with quick-connect plug
Draw-through design, easy slide-out blowers and quick connect plug
Controls and motors are factory-wired and terminated in a junction box for single-point power supply
One-inch duct collar on return- and supply-air openings
Protective covers keep the grille openings free of debris during shipment and construction
Individually tagged, crated and shipped as scheduled for installation
ETL and AHRI certified; 100% factory tested

Accessories

Accessories Options

Valve package controls – wide selection of factory-mounted valves and controls
Pedestal base
Outside air openings
- Manual
- Motorized
Thermostats
Condensate float switch
Condensate pumps
Pedestal base

Dimensions

Options

Systems

DX
Chilled-Water
Hot-Water
Electric Resistance
Steam

In any combination of the above

Insulation

Thickness up to 1″
Fiberglass
Foil-face
Elastomeric

Coil

Copper fins/tubes
Phenolic-coated
Stainless-steel end plates
Right left or top connections
TXV – factory-mounted
Freeze protection
Custom fin spacing

Drain Pan

Stainless-steel
Extended
Drip tray
Condensate float switch
Condensate pumps

Cabinets

Marine duty
Extensions
Pedestal base
Front-return air grille
Return-air grille

Electrical

Motors
- 115, 208, 230 and 277
- Single or three phase
- 50 or 60Hz
- ECM
Line or low voltage
1 to 8 kW electric resistance heat
Disconnects
- Fused
- Non-fused
Condensate float switch
Condensate pumps
Thermostats
UV Light
Controls
Flow control

Further Information

None available with this product.