Vertical Wall Mount

Low Silhouette Front Discharge Vertical Painted Cabinet

Part Number: F2-F

The Vertical Low-Silhouette Front Discharge (F2-F) is a low-static (up to .25 ESP) fan coil with a blow-through design. The F2-F fan coil comes with a coil, blower/motor assembly with quick-connect plug and a galvanized steel, powder-coated epoxy drain pan covered with ⅛-inch thick insulation. The galvanized steel cabinet is insulated with ½-inch thick, over three pound density, neoprene-coated fiberglass. The F2-F cabinet and top control access panel are finished in a soft-white powder-coat epoxy with black bar-type front-discharge and return-air grilles. Freestanding at 14½-inches in height, two F2-F units may be used side by side allowing for unlimited movement of drapes and blinds at peak performance.

Cooling Capacity

F2 Series vertical fan coils have been rated in accordance with AHRI Standard 440-2005 for room fan-coils air-conditioners and are certified by AHRI to meet the following product performance ratings:

Based on 80°F DB and 67°F WB EAT, 45°F EWT, 10°F temperature rise, high fan speed. Motor voltage 115/1/60 power source.
Air flow under dry coil conditions. Water pressure drops shown in feet of water.

Heating Performance

Notes: 1) Based on 70°F DB EAT, 180°F EWT, 40°F temperature drop, high fan speed. Motor voltage 115/1/60 power source.
Air flow under dry coil conditions. Water pressure drops shown in feet of water.

Features

400 and 600 CFM
The unit consists of heavy-gauge galvanized chassis, a drain pan, filter, motor/blower assembly and an attractive, top-discharge cabinet
Designed for exposed under-the-window applications
Cabinet and top control access panel are soft-white, powder-coated epoxy finish with black, bar-type front-discharge and return-air grilles
The attractive, streamlined cabinetry blends with any room décor
Coils are limited to four rows, two units may be set side-by-side where 800 to 1,200 CFM is required
Blow-through design
Coils are manufactured of copper tube with aluminum fins and are 100% underwater pressure tested to 350 PSI with a 300 PSI working pressure
Galvanized drain pan is finished with a powder-coated epoxy and covered with 1/8″ thick insulation
Heavy-gauge galvanized steel cabinet insulated with 1/2″ thick, over three-pound density, neoprene-coated fiberglass
Three-speed, 115/1/60 motor with quick-connect plug
Controls and motors are factory-wired and terminated in a junction box for single-point power supply
One-inch fiberglass, throwaway filter
Rear mounting holes provided for wall mounting
Protective covers keep the grille openings free of debris during shipment and construction
Individually tagged, crated and shipped as scheduled for installation
ETL and AHRI certified; 100% factory tested

Accessories

Accessories Options

Valve package controls – wide selection of factory-mounted valves and controls
Outside air dampers/wall boxes
- Manual
- Motorized
- Bug screens
- Leveling legs
TXV – factory-mounted
Condensate float switch
Condensate pumps
Thermostats

Dimensions

Options

Systems

DX
Chilled-Water
Hot-Water
Electric Resistance
Steam

In any combination of the above

Insulation

Thickness up to 1″
Fiberglass
Foil-face
Elastomeric

Coil

Copper fins/tubes
Phenolic-coated
Stainless-steel end plates
Right or left connections
TXV – factory-mounted
Freeze protection
Custom fin spacing

Drain Pan

Stainless-steel
Extended
Drip tray
Condensate float switch
Condensate pumps

Cabinets

Marine duty
Custom paint
Extensions
Heavier steel gauges
False back
Sub-base

Electrical

Motors
- 115, 208, 230 and 277
- Single or three phase
- 50 or 60Hz
- ECM
Line or low voltage
1 to 5 kW electric resistance heat
Disconnects
- Fused
- Non-fused
Condensate float switch
Condensate pumps
Thermostats
UV light
Controls
Flow Control

Further Information

None available with this product.